Featured Research

from universities, journals, and other organizations

Better Metal Forming: Magnetic Pulses "Bump" Metal Into Shape

Date:
October 17, 2002
Source:
Ohio State University
Summary:
A process developed at Ohio State University for shaping metal parts using magnetism has reached a new milestone -- one that may cut manufacturing costs and help preserve the environment. The process could also expand manufacturers' choice of available metals, and enable the use of aluminum parts in lighter, fuel-efficient automobiles.

COLUMBUS, Ohio -- A process developed at Ohio State University for shaping metal parts using magnetism has reached a new milestone -- one that may cut manufacturing costs and help preserve the environment.

Related Articles


The process could also expand manufacturers' choice of available metals, and enable the use of aluminum parts in lighter, fuel-efficient automobiles.

Glenn S. Daehn, professor of materials science and engineering, and his colleagues pioneered hybrid electromagnetic metal forming in 1999, while collaborating with the "Big Three" automakers. With this process, a traditional tool and die stamps the general shape of a part out of sheet metal. Afterward, a magnetic field pushes at specific locations of the sheet metal to form fine details or complex shapes.

Now the Ohio State engineers have discovered that they can improve the process if they use the magnetic field to stretch certain portions of the metal during the stamping operation.

In tests, they were able to create an aluminum pan with a depth nearly 1.5 times greater than previously possible, and they did so without relying upon the potentially toxic industrial lubricants normally required for stamping.

Daehn described the improved process Oct. 9 in Columbus, OH, at the annual meeting of the Minerals, Metals, and Materials Society, now known as TMS.

Daehn calls the process "bump forming," because the magnetic field bumps against the metal in many short pulses -- typically 5 to 20 times in less than one second -- while the metal moves into the die.

Normally, as a sheet of metal bends to fit inside a tool and die, some parts of the sheet stretch more than others. These are the parts that may tear if the metal stretches too much.

With Daehn's technique, electromagnetic fields work against the parts of the sheet that would not normally stretch, causing them to bow out. With this extra amount of "give" in the metal, other portions of the sheet will be less likely to tear.

The process works well in electrically conductive metals, including aluminum. When exposed to a strong electromagnetic field from a coil inside the punch portion of the stamping tool, a corresponding electrical current and electromagnetic field form inside the metal. The field in the coil and the field in the metal repel each other, pushing the aluminum away from the punch.

Bump forming could be very useful in mass production, Daehn said. From the auto industry to aerospace and electronics, large manufacturing operations often need to stamp as many as 10 million copies of their metal components per year.

"The process has to be reliable, and require as little human intervention as possible," Daehn said. "In automobile production especially, manufactures need to make parts in as few steps as they possibly can. I think we can do a lot of good things for industry with this technique."

Daehn and Ohio State postdoctoral researcher Vincent J. Vohnout developed their bump forming technique with Ishikawajima-Harima Heavy Industries Co., Ltd., one of the largest manufacturing companies in Japan.

Using automotive-grade aluminum, the engineers stamped out a shape similar to a baking pan. Because aluminum tears easily, manufacturers typically need to coat the metal with lubricant in order to stamp it, Daehn explained. The potentially hazardous liquid is then washed from the metal and disposed of, at a significant cost.

With conventional stamping equipment and lubricant, the deepest pan they could create without tearing the aluminum was 1.7 inches (4.4 centimeters). After placing electromagnetic actuators in the same equipment and using the bump forming procedure, they were able to stamp a pan 2.5 inches (6.4 centimeters) deep -- a 47 percent increase.

Most significant to Daehn is that they were able to make a deeper impression using the same stamping pressure, and without using any lubricant.

Daehn counted off several potential benefits for industry.

"We can enable the use of higher strength materials and aluminum alloys in manufacturing. We can reduce the amount of equipment associated with metal forming. Parts that used to require multiple steps could be made with one set of tooling, which would mean a big cost savings. And we think we can eliminate reliance on these nasty lubricants," he said.

From start to finish, the bump forming process can be designed to take five seconds or less per part, which would fit in with typical manufacturing cycles.

Daehn and Vohnout patented their bump forming process, and are seeking further funding to develop it. The National Science Foundation has largely funded the work thus far.


Story Source:

The above story is based on materials provided by Ohio State University. Note: Materials may be edited for content and length.


Cite This Page:

Ohio State University. "Better Metal Forming: Magnetic Pulses "Bump" Metal Into Shape." ScienceDaily. ScienceDaily, 17 October 2002. <www.sciencedaily.com/releases/2002/10/021017072237.htm>.
Ohio State University. (2002, October 17). Better Metal Forming: Magnetic Pulses "Bump" Metal Into Shape. ScienceDaily. Retrieved October 31, 2014 from www.sciencedaily.com/releases/2002/10/021017072237.htm
Ohio State University. "Better Metal Forming: Magnetic Pulses "Bump" Metal Into Shape." ScienceDaily. www.sciencedaily.com/releases/2002/10/021017072237.htm (accessed October 31, 2014).

Share This



More Matter & Energy News

Friday, October 31, 2014

Featured Research

from universities, journals, and other organizations


Featured Videos

from AP, Reuters, AFP, and other news services

Jaguar Land Rover Opens $800 Million Factory in Britain

Jaguar Land Rover Opens $800 Million Factory in Britain

AFP (Oct. 30, 2014) British luxury car manufacturer Jaguar Land Rover opened a $800 million engine manufacturing centre in western England, creating 1,400 jobs. Duration: 00:45 Video provided by AFP
Powered by NewsLook.com
SkyCruiser Concept Claims to Solve Problem With Flying Cars

SkyCruiser Concept Claims to Solve Problem With Flying Cars

Buzz60 (Oct. 30, 2014) A start-up company called Krossblade says its SkyCruiser concept flying car solves the problem with most flying car concepts. Mara Montalbano (@maramontalbano) explains. Video provided by Buzz60
Powered by NewsLook.com
Mind-Controlled Prosthetic Arm Restores Amputee Dexterity

Mind-Controlled Prosthetic Arm Restores Amputee Dexterity

Reuters - Innovations Video Online (Oct. 29, 2014) A Swedish amputee who became the first person to ever receive a brain controlled prosthetic arm is able to manipulate and handle delicate objects with an unprecedented level of dexterity. The device is connected directly to his bone, nerves and muscles, giving him the ability to control it with his thoughts. Matthew Stock reports. Video provided by Reuters
Powered by NewsLook.com
Robots Get Funky on the Dance Floor

Robots Get Funky on the Dance Floor

AP (Oct. 29, 2014) Dancing, spinning and fighting robots are showing off their agility at "Robocomp" in Krakow. (Oct. 29) Video provided by AP
Powered by NewsLook.com

Search ScienceDaily

Number of stories in archives: 140,361

Find with keyword(s):
Enter a keyword or phrase to search ScienceDaily for related topics and research stories.

Save/Print:
Share:

Breaking News:

Strange & Offbeat Stories


Space & Time

Matter & Energy

Computers & Math

In Other News

... from NewsDaily.com

Science News

Health News

Environment News

Technology News



Save/Print:
Share:

Free Subscriptions


Get the latest science news with ScienceDaily's free email newsletters, updated daily and weekly. Or view hourly updated newsfeeds in your RSS reader:

Get Social & Mobile


Keep up to date with the latest news from ScienceDaily via social networks and mobile apps:

Have Feedback?


Tell us what you think of ScienceDaily -- we welcome both positive and negative comments. Have any problems using the site? Questions?
Mobile: iPhone Android Web
Follow: Facebook Twitter Google+
Subscribe: RSS Feeds Email Newsletters
Latest Headlines Health & Medicine Mind & Brain Space & Time Matter & Energy Computers & Math Plants & Animals Earth & Climate Fossils & Ruins