Featured Research

from universities, journals, and other organizations

More Efficient Wind Turbine Blade Designed

Date:
March 20, 2007
Source:
Sandia National Laboratories
Summary:
A new wind turbine blade design that researchers at Sandia developed in partnership with Knight & Carver of San Diego should significantly reduce the cost-of-energy of wind turbines at low-wind-speed sites. Named "STAR" for Sweep Twist Adaptive Rotor, the blade is the first of its kind produced at a utility-grade size.

Proof load testing on new Sweep Twist Adaptive Rotor blade using 55-gallon drums to test blade strength.
Credit: Image courtesy of Sandia National Laboratories

A new wind turbine blade design that researchers at Sandia National Laboratories developed in partnership with Knight & Carver (K&C) of San Diego promises to be more efficient than current designs. It should significantly reduce the cost-of-energy (COE) of wind turbines at low-wind-speed sites.

Related Articles


Named "STAR" for Sweep Twist Adaptive Rotor, the blade is the first of its kind produced at a utility-grade size. Its most distinctive characteristic is a gently curved tip, termed "sweep," which unlike the vast majority of blades in current use, is specially designed for low-wind-speed regions like the Midwest. The sites targeted by this effort have annual average wind speeds of 5.8 meters per second, measured at 10-meter height. Such sites are abundant in the U.S. and would increase by 20-fold the available land area that can be economically developed for wind energy.

Sized at 27.1 meters - almost three meters longer than the baseline it will replace - the blade improves energy capture at lower wind speeds. Instead of the traditional linear shape, the blade features a curvature toward the trailing edge, which allows the blade to respond to turbulent gusts in a manner that lowers fatigue loads on the blade. It is made of fiberglass and epoxy resin.

"This design allows the blade to twist more than traditional designs, thus relieving some of the effects of gusty turbulent wind on blade life," says Tom Ashwill, who leads Sandia's blade research efforts. "This then allows us to grow the blade length for the same rotor, providing for increased energy capture of 5-10 percent and yet retaining the same expected fatigue life."

Sandia is a National Nuclear Security Administration (NNSA) laboratory.

The K&C contract is part of the Low Wind Speed Technology (LWST) project that targets wind sites that are not the strongest but plentiful. In late 2005 the Department of Energy (DOE) and Sandia awarded Knight & Carver the $2 million contract that includes $800,000 in K&C cost share. Because of budget reallocations, this project was the only one of several LWST projects to receive 2007 funding.

Sandia's role in the project has been in directing design and test planning. The K&C team provided the detailed design and blade fabrication.

The first STAR blade was tested in January at Knight & Carver's fabrication facility in San Diego to determine its bending and twist behavior due to static loads. Natural frequencies were also measured. This data will be compared to design simulations to determine how well the design concept performs. Four additional blades will be fabricated in the first quarter of 2007 - three of which will be flight-tested on a turbine in Iowa.

"The DOE interest and funding are a big step for us," Ashwill says. "We've been pushing for the incorporation of innovative concepts into utility-scale blades for some time now as a way of reaching program goals of lowered cost of energy."

He adds that the continued increase in the average size of utility-grade wind turbines may come to an end before all efficiencies are wrung out unless blade weight growth (which is nonlinear) can be reined in. The challenge is to develop new concepts that reduce the rate of weight growth, such as the swept STAR blade.

Other weight-reducing concepts such as carbon spar caps, off-axis carbon fibers that facilitate bend-twist coupling, and new "structural" airfoils have been incorporated at a smaller scale in 9-meter-long prototype blade being flight-tested at Sandia's test site in Bushland, Texas, at the U.S. Department of Agriculture ARS (Agriculture Research Station) facility.

Other members of the design team are Dynamic Design of Davis, Calif.; MDZ Consulting of Clear Lake Shores, Texas; University of California, Davis; and NSE Composites of Seattle, Wash.


Story Source:

The above story is based on materials provided by Sandia National Laboratories. Note: Materials may be edited for content and length.


Cite This Page:

Sandia National Laboratories. "More Efficient Wind Turbine Blade Designed." ScienceDaily. ScienceDaily, 20 March 2007. <www.sciencedaily.com/releases/2007/03/070319180042.htm>.
Sandia National Laboratories. (2007, March 20). More Efficient Wind Turbine Blade Designed. ScienceDaily. Retrieved October 31, 2014 from www.sciencedaily.com/releases/2007/03/070319180042.htm
Sandia National Laboratories. "More Efficient Wind Turbine Blade Designed." ScienceDaily. www.sciencedaily.com/releases/2007/03/070319180042.htm (accessed October 31, 2014).

Share This



More Matter & Energy News

Friday, October 31, 2014

Featured Research

from universities, journals, and other organizations


Featured Videos

from AP, Reuters, AFP, and other news services

Jaguar Land Rover Opens $800 Million Factory in Britain

Jaguar Land Rover Opens $800 Million Factory in Britain

AFP (Oct. 30, 2014) British luxury car manufacturer Jaguar Land Rover opened a $800 million engine manufacturing centre in western England, creating 1,400 jobs. Duration: 00:45 Video provided by AFP
Powered by NewsLook.com
SkyCruiser Concept Claims to Solve Problem With Flying Cars

SkyCruiser Concept Claims to Solve Problem With Flying Cars

Buzz60 (Oct. 30, 2014) A start-up company called Krossblade says its SkyCruiser concept flying car solves the problem with most flying car concepts. Mara Montalbano (@maramontalbano) explains. Video provided by Buzz60
Powered by NewsLook.com
Mind-Controlled Prosthetic Arm Restores Amputee Dexterity

Mind-Controlled Prosthetic Arm Restores Amputee Dexterity

Reuters - Innovations Video Online (Oct. 29, 2014) A Swedish amputee who became the first person to ever receive a brain controlled prosthetic arm is able to manipulate and handle delicate objects with an unprecedented level of dexterity. The device is connected directly to his bone, nerves and muscles, giving him the ability to control it with his thoughts. Matthew Stock reports. Video provided by Reuters
Powered by NewsLook.com
Robots Get Funky on the Dance Floor

Robots Get Funky on the Dance Floor

AP (Oct. 29, 2014) Dancing, spinning and fighting robots are showing off their agility at "Robocomp" in Krakow. (Oct. 29) Video provided by AP
Powered by NewsLook.com

Search ScienceDaily

Number of stories in archives: 140,361

Find with keyword(s):
Enter a keyword or phrase to search ScienceDaily for related topics and research stories.

Save/Print:
Share:

Breaking News:

Strange & Offbeat Stories


Space & Time

Matter & Energy

Computers & Math

In Other News

... from NewsDaily.com

Science News

Health News

Environment News

Technology News



Save/Print:
Share:

Free Subscriptions


Get the latest science news with ScienceDaily's free email newsletters, updated daily and weekly. Or view hourly updated newsfeeds in your RSS reader:

Get Social & Mobile


Keep up to date with the latest news from ScienceDaily via social networks and mobile apps:

Have Feedback?


Tell us what you think of ScienceDaily -- we welcome both positive and negative comments. Have any problems using the site? Questions?
Mobile: iPhone Android Web
Follow: Facebook Twitter Google+
Subscribe: RSS Feeds Email Newsletters
Latest Headlines Health & Medicine Mind & Brain Space & Time Matter & Energy Computers & Math Plants & Animals Earth & Climate Fossils & Ruins