Featured Research

from universities, journals, and other organizations

Space industry: Does 3-D printing have the right stuff?

Date:
June 25, 2014
Source:
European Space Agency
Summary:
3D-printed parts promise a revolution in the space industry, rapidly creating almost any object needed. But do the results really have the right stuff for flying in space? The European Space Agency is now checking if their surface finish comes up to scratch.

Scanning electron microscope close-up of the surface of a part produced by Additive Manufacturing, otherwise known as 3D-printing. As a consequence of its manufacture, loose particles adhere to the solid surface, which could be troubling for use in space. The largest particles seen measure about 100 micrometres across, around the width of an average human hair.
Credit: ESA

3D-printed parts promise a revolution in the space industry, rapidly creating almost any object needed. But do the results really have the right stuff for flying in space? ESA is now checking if their surface finish comes up to scratch.

3D printing involves building an item by laying down successive layers of material, rather than cutting away from a solid block.

ESA's Clean Space initiative continues to look at ways of reducing the environmental impacts of space technologies -- and 3D printing slashes waste.

Extremely complex parts can be printed and made as light as possible, but there's a catch: 3D printing tends to end up with rougher surfaces than their traditional counterparts.

While this is not a major issue for terrestrial applications, there could be important consequences for their use in space. As Nobel-winning chemist Linus Pauli once observed: "'God made solids but the devil made surfaces."

Traditionally, materials used in space have to be as smoothly finished as possible, with no loose particles or pores that might develop cracks. They have to be clean, to surgical standards. Delicate satellite electronics or optics have in the past been fatally damaged by particle contamination or outgassing.

A new ESA project will investigate the surface features of 3D-printed parts to scrutinise the suitability of standard surface treatments for typical satellite materials such as aluminium, titanium and stainless steel.

Different manufacturing techniques, including laser and electron beam melting, will be assessed, along with surface treatments such as sandblasting, etching, nickel coating and painting.

The mechanical properties of the processed parts will be assessed for resistance to stress corrosion and the tendency to fracture.

The usefulness of 'non-destructive' investigations such as ultrasound and X-ray examinations will be evaluated as methods for ensuring the soundness of the parts.

These samples will also be tested against the high humidity found at ESA's equatorial launch site in South America, as well as against the temperature extremes found in space.

Companies can tender for the project through ESA's tendering system (http://www.esa.int/About_Us/Industry/Industry_how_to_do_business/ESA_s_Invitation_to_Tender_System_EMITS).


Story Source:

The above story is based on materials provided by European Space Agency. Note: Materials may be edited for content and length.


Cite This Page:

European Space Agency. "Space industry: Does 3-D printing have the right stuff?." ScienceDaily. ScienceDaily, 25 June 2014. <www.sciencedaily.com/releases/2014/06/140625133309.htm>.
European Space Agency. (2014, June 25). Space industry: Does 3-D printing have the right stuff?. ScienceDaily. Retrieved July 29, 2014 from www.sciencedaily.com/releases/2014/06/140625133309.htm
European Space Agency. "Space industry: Does 3-D printing have the right stuff?." ScienceDaily. www.sciencedaily.com/releases/2014/06/140625133309.htm (accessed July 29, 2014).

Share This




More Space & Time News

Tuesday, July 29, 2014

Featured Research

from universities, journals, and other organizations


Featured Videos

from AP, Reuters, AFP, and other news services

Russia Saves Gecko Sex Satellite, Media Has Some Fun With It

Russia Saves Gecko Sex Satellite, Media Has Some Fun With It

Newsy (July 27, 2014) The satellite is back under ground control after a tense few days, but with a gecko sex experiment on board, the media just couldn't help themselves. Video provided by Newsy
Powered by NewsLook.com
NASA EDGE: OCO-2 Launch

NASA EDGE: OCO-2 Launch

NASA (July 25, 2014) NASA EDGE webcasts live from Vandenberg AFB for the launch of the Oribiting Carbon Observatory-2 (OCO) launch. Video provided by NASA
Powered by NewsLook.com
This Week @ NASA, July 25, 2014

This Week @ NASA, July 25, 2014

NASA (July 25, 2014) Apollo 11 celebration, Next Giant Leap anticipation, ISS astronauts appear in the House and more... Video provided by NASA
Powered by NewsLook.com
Space to Ground: Coming and Going

Space to Ground: Coming and Going

NASA (July 25, 2014) One station cargo ship leaves, another arrives, aquatic research and commercial spinoffs. Questions or comments? Use #spacetoground to talk to us. Video provided by NASA
Powered by NewsLook.com

Search ScienceDaily

Number of stories in archives: 140,361

Find with keyword(s):
Enter a keyword or phrase to search ScienceDaily for related topics and research stories.

Save/Print:
Share:

Breaking News:
from the past week

In Other News

... from NewsDaily.com

Science News

Health News

Environment News

Technology News



Save/Print:
Share:

Free Subscriptions


Get the latest science news with ScienceDaily's free email newsletters, updated daily and weekly. Or view hourly updated newsfeeds in your RSS reader:

Get Social & Mobile


Keep up to date with the latest news from ScienceDaily via social networks and mobile apps:

Have Feedback?


Tell us what you think of ScienceDaily -- we welcome both positive and negative comments. Have any problems using the site? Questions?
Mobile: iPhone Android Web
Follow: Facebook Twitter Google+
Subscribe: RSS Feeds Email Newsletters
Latest Headlines Health & Medicine Mind & Brain Space & Time Matter & Energy Computers & Math Plants & Animals Earth & Climate Fossils & Ruins