Featured Research

from universities, journals, and other organizations

'Comb on a chip' powers new atomic clock design

Date:
July 22, 2014
Source:
National Institute of Standards and Technology (NIST)
Summary:
Researchers have demonstrated a novel design for a small atomic clock that is based on a chip-scale frequency comb, or a microcomb.

This image depicts NIST physicists Scott Diddams (left) and Scott Papp with a prototype atomic clock based on a chip-scale frequency comb. Diddams is holding the silicon chip, which fits into the clock apparatus on the table. With performance improvements and further reductions in size, the technology might eventually be used to make portable tools for measuring time and frequency.
Credit: Burrus/NIST

Researchers from the National Institute of Standards and Technology (NIST) and California Institute of Technology (Caltech) have demonstrated a new design for an atomic clock that is based on a chip-scale frequency comb, or a microcomb.

The microcomb clock, featured on the cover of the inaugural issue of the new journal Optica, is the first demonstration of all-optical control of the microcomb, and its accurate conversion of optical frequencies to lower microwave frequencies. (Optical frequencies are too high to count; microwave frequencies can be counted with electronics.)

The new clock architecture might eventually be used to make portable tools for calibrating frequencies of advanced telecommunications systems or providing microwave signals to boost stability and resolution in radar, navigation and scientific instruments. The technology also has potential to combine good timekeeping precision with very small size. The comb clock might be a component of future "NIST on a chip" technologies offering multiple measurement methods and standards in a portable form.

"The microcomb clock is one way we might get precision frequency metrology tools out of the lab and into real-world settings," NIST physicist Scott Diddams says.

Frequency combs produce precisely defined colors, or frequencies, of light that are evenly spaced throughout the comb's range. (The name comes from the spectrum's resemblance to the teeth of a pocket comb.) The original combs required relatively large lasers that produced rapid, extremely short pulses of light, but more recently NIST and other laboratories have developed much smaller microcombs.

A microcomb generates its set of frequencies from light that gets trapped in the periphery of a tiny silica glass disk, looping around and around the perimeter. These combs can be astonishingly stable. NIST has an ongoing collaboration in this area with Caltech researchers, who made the 2-millimeter-wide silica disk that generates the frequency comb for the new clock.

The new microcomb clock uses a laser to excite the Caltech disk to generate a frequency comb, broadens the spectrum using nonlinear fiber, and stabilizes two comb teeth (individual frequencies) to energy transitions in rubidium atoms that "tick" at optical frequencies. (Conventional rubidium atomic clocks operate at much lower microwave frequencies.) The comb converts these optical frequency ticks to the microwave domain.

Thanks to the gear-like properties of the disk and the comb, the output is also 100 times more stable than the intrinsic ticking of the rubidium atoms. According to Diddams, "A simple analogy is that of a mechanical clock: The rubidium atoms provide stable oscillations -- a pendulum -- and the microcomb is like a set of gears that synthesizes optical and microwave frequencies."

The center of the comb spectrum is locked to an infrared laser operating at 1560 nanometers, a wavelength used in telecommunications.

NIST researchers have not yet systematically analyzed the microcomb clock's precision. The prototype uses a tabletop-sized rubidium reference. The scientists expect to reduce the instrument size by switching to a miniature container of atoms like that used in NIST's original chip-scale atomic clock. Scientists also hope to find a more stable atomic reference.

The microcomb chip was made by use of conventional semiconductor fabrication techniques and, therefore, could be mass produced and integrated with other chip-scale components such as lasers and atomic references. NIST researchers expect that, with further research, the microcomb clock architecture can achieve substantially better performance in the future.

The research is supported in part by the Defense Advanced Research Projects Agency and National Aeronautics and Space Administration.


Story Source:

The above story is based on materials provided by National Institute of Standards and Technology (NIST). Note: Materials may be edited for content and length.


Journal Reference:

  1. Scott B. Papp, Katja Beha, Pascal Del’Haye, Franklyn Quinlan, Hansuek Lee, Kerry J. Vahala, Scott A. Diddams. Microresonator frequency comb optical clock. Optica, 2014; 1 (1): 10 DOI: 10.1364/OPTICA.1.000010

Cite This Page:

National Institute of Standards and Technology (NIST). "'Comb on a chip' powers new atomic clock design." ScienceDaily. ScienceDaily, 22 July 2014. <www.sciencedaily.com/releases/2014/07/140722111920.htm>.
National Institute of Standards and Technology (NIST). (2014, July 22). 'Comb on a chip' powers new atomic clock design. ScienceDaily. Retrieved September 16, 2014 from www.sciencedaily.com/releases/2014/07/140722111920.htm
National Institute of Standards and Technology (NIST). "'Comb on a chip' powers new atomic clock design." ScienceDaily. www.sciencedaily.com/releases/2014/07/140722111920.htm (accessed September 16, 2014).

Share This



More Matter & Energy News

Tuesday, September 16, 2014

Featured Research

from universities, journals, and other organizations


Featured Videos

from AP, Reuters, AFP, and other news services

Manufacturer Prints 3-D Car In Record Time

Manufacturer Prints 3-D Car In Record Time

Newsy (Sep. 15, 2014) — Automobile manufacturer Local Motors created a drivable electric car using a 3-D printer. Printing the body only took 44 hours. Video provided by Newsy
Powered by NewsLook.com
Refurbished New York Subway Tunnel Unveiled After Sandy Damage

Refurbished New York Subway Tunnel Unveiled After Sandy Damage

Reuters - US Online Video (Sep. 15, 2014) — New York officials unveil subway tunnels that were refurbished after Superstorm Sandy. Nathan Frandino reports. Video provided by Reuters
Powered by NewsLook.com
Frustration As Drone Industry Outpaces Regulation In U.S.

Frustration As Drone Industry Outpaces Regulation In U.S.

Newsy (Sep. 14, 2014) — U.S. firms worry they’re falling behind in the marketplace as the FAA considers how to regulate commercial drones. Video provided by Newsy
Powered by NewsLook.com
Smart Gun Innovators Fear Backlash From Gun Rights Advocates

Smart Gun Innovators Fear Backlash From Gun Rights Advocates

Newsy (Sep. 14, 2014) — Winners of a contest for smart gun design are asking not to be named after others in the industry received threats for marketing similar products. Video provided by Newsy
Powered by NewsLook.com

Search ScienceDaily

Number of stories in archives: 140,361

Find with keyword(s):
 
Enter a keyword or phrase to search ScienceDaily for related topics and research stories.

Save/Print:
Share:  

Breaking News:
from the past week

In Other News

... from NewsDaily.com

Science News

Health News

Environment News

Technology News



Save/Print:
Share:  

Free Subscriptions


Get the latest science news with ScienceDaily's free email newsletters, updated daily and weekly. Or view hourly updated newsfeeds in your RSS reader:

Get Social & Mobile


Keep up to date with the latest news from ScienceDaily via social networks and mobile apps:

Have Feedback?


Tell us what you think of ScienceDaily -- we welcome both positive and negative comments. Have any problems using the site? Questions?
Mobile iPhone Android Web
Follow Facebook Twitter Google+
Subscribe RSS Feeds Email Newsletters
Latest Headlines Health & Medicine Mind & Brain Space & Time Matter & Energy Computers & Math Plants & Animals Earth & Climate Fossils & Ruins